Category:1055 Concrete Curing Material - Revision history

Hoskir: updated links to 106.12

2024-12-13T15:34:42Z

updated links to 106.12

Hoskir: updated per RR3768

2023-09-28T13:01:50Z

updated per RR3768

Smithk: /* 1055.3.2 Dissipating Curing Compound */ Per CM, replaced archaic "Automation Section" with AWP MA Sample Record, General

2021-11-24T14:15:09Z

1055.3.2 Dissipating Curing Compound: Per CM, replaced archaic "Automation Section" with AWP MA Sample Record, General

← Older revision		Revision as of 09:15, 24 November 2021
Line 74:		Line 74:
	===1055.3.2 Dissipating Curing Compound===		===1055.3.2 Dissipating Curing Compound===

	A sample record as described by [~~[106.20 Reporting#106.20.1.1 Automation Section\|EPG 106~~.20.1.~~1 Automation Section]~~] and including the Free Form Test will be created for any material accepted on the job on the basis of certifications, label, or invoice.		A sample record as described in [https://epg.modot.org/forms/CM/AWP_MA_Sample_Record_General.docx AWP MA Sample Record, General] and including the Free Form Test will be created for any material accepted on the job on the basis of certifications, label, or invoice.

	If the shipper requests, the material will be assigned a PAL ID per EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds.		If the shipper requests, the material will be assigned a PAL ID per EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds.

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-10-18T13:40:27Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 08:40, 18 October 2021
Line 40:		Line 40:

	====1055.2.1.6 Sample====		====1055.2.1.6 Sample====
	A sample of curing compound shall consist of one quart (1 liter) of material in a screw top can. All samples shall be obtained by the manufacturer or contractor’s agent in accordance with the manufacturer’s sampling instructions. The inspector will observe the sampling process. The sample shall be recorded through ~~SiteManager~~ showing the manufacturer's name, the brand name and designation of the material, lot number, net quantity represented, and the location where the sample was obtained using the Sampled From and Sample Origin fields of ~~SiteManager~~. The Other tab is also used for a Mixing Facility. The PAL ID number obtained by the supplier in accordance with EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds should be recorded in Site Manager in the “Link To” field.		A sample of curing compound shall consist of one quart (1 liter) of material in a screw top can. All samples shall be obtained by the manufacturer or contractor’s agent in accordance with the manufacturer’s sampling instructions. The inspector will observe the sampling process. The sample shall be recorded through AASHTOWARE Project (AWP) showing the manufacturer's name, the brand name and designation of the material, lot number, net quantity represented, and the location where the sample was obtained using the Sampled From and Sample Origin fields of AWP. The Other tab is also used for a Mixing Facility. The PAL ID number obtained by the supplier in accordance with EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds should be recorded in Site Manager in the “Link To” field.

	===1055.2.2 Dissipating Curing Compound===		===1055.2.2 Dissipating Curing Compound===
Line 60:		Line 60:

	====1055.2.3.2 Sampling====		====1055.2.3.2 Sampling====
	Sampling will be designated by the State Construction and Materials Engineer or when specification compliance is suspect. When a shipment is sampled, the number of rolls to be sampled is one-half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing and identified through ~~SiteManager~~.		Sampling will be designated by the State Construction and Materials Engineer or when specification compliance is suspect. When a shipment is sampled, the number of rolls to be sampled is one-half the square root of the number of rolls, rounded to the nearest whole number, in the shipment. A sample is to consist of a strip 18 in. (450 mm) long by the width of the roll and is to be cut at least 5 ft. (1500 mm) from the end of the roll. The samples are to be submitted to the Laboratory for testing and identified through AWP.

	==1055.3 Sample Record ==		==1055.3 Sample Record ==
Line 70:		Line 70:
	For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [https://www.modot.org/sites/default/files/documents/construction_and_materials/material_qualified_product_listing/gs013f3.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.		For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [https://www.modot.org/sites/default/files/documents/construction_and_materials/material_qualified_product_listing/gs013f3.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.

	Material purchased for maintenance work may be accepted solely on the basis of the PAL supplier, or manufacturer and brand being on the Pre-Acceptance List. District materials will report the receipt and acceptance of the material in ~~SiteManager~~ and will mark the material or containers with the sample ID number they assign.		Material purchased for maintenance work may be accepted solely on the basis of the PAL supplier, or manufacturer and brand being on the Pre-Acceptance List. District materials will report the receipt and acceptance of the material in AWP and will mark the material or containers with the sample ID number they assign.

	===1055.3.2 Dissipating Curing Compound===		===1055.3.2 Dissipating Curing Compound===

Smithk: Per CM, updated GS-13 form links

2021-04-22T14:09:34Z

Per CM, updated GS-13 form links

← Older revision		Revision as of 09:09, 22 April 2021
Line 11:		Line 11:
	\|'''Form'''		\|'''Form'''
	\|-		\|-
	\|[~~http~~://www.modot.~~mo.gov~~/~~business~~/~~materials~~/~~pdf~~/~~vol_1~~/~~GS013F3~~.pdf GS-13 Form 3]		\|[https://www.modot.org/sites/default/files/documents/construction_and_materials/material_qualified_product_listing/gs013f3.pdf GS-13 Form 3]
	\|-		\|-
	\|'''MGS Information'''		\|'''MGS Information'''
Line 68:		Line 68:
	Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.12 Pre-Acceptance Lists (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]].		Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.12 Pre-Acceptance Lists (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]].

	For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [~~http~~://www.modot.~~mo.gov~~/~~business~~/~~materials~~/~~pdf~~/~~vol_1~~/~~GS013F3~~.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.		For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [https://www.modot.org/sites/default/files/documents/construction_and_materials/material_qualified_product_listing/gs013f3.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.

	Material purchased for maintenance work may be accepted solely on the basis of the PAL supplier, or manufacturer and brand being on the Pre-Acceptance List. District materials will report the receipt and acceptance of the material in SiteManager and will mark the material or containers with the sample ID number they assign.		Material purchased for maintenance work may be accepted solely on the basis of the PAL supplier, or manufacturer and brand being on the Pre-Acceptance List. District materials will report the receipt and acceptance of the material in SiteManager and will mark the material or containers with the sample ID number they assign.

Smithk: updated link

2018-10-16T12:58:27Z

updated link

← Older revision		Revision as of 07:58, 16 October 2018
Line 15:		Line 15:
	\|'''MGS Information'''		\|'''MGS Information'''
	\|-		\|-
	\|[~~http~~://www.modot.~~mo.gov/business/materials/pdf~~/mgs~~/MGSINDEX.pdf~~ Current General Services Specifications (MGS) By Subject]		\|[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject]
	\|}		\|}

Smithk: updated links

2016-06-15T17:48:25Z

updated links

← Older revision		Revision as of 12:48, 15 June 2016
Line 1:		Line 1:
	[[image:1055.jpg\|right\|400px]]		[[image:1055.jpg\|right\|400px]]
	This article establishes procedures for the inspection, [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] and reporting of clear or transparent liquid curing compound, white pigmented curing compound, dissipating curing compound, waterproof paper, white polyethylene-burlap sheeting and burlap and mats. Refer to [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec1055~~.pdf Sec 1055] for MoDOT’s specifications.		This article establishes procedures for the inspection, [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] and reporting of clear or transparent liquid curing compound, white pigmented curing compound, dissipating curing compound, waterproof paper, white polyethylene-burlap sheeting and burlap and mats. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1055] for MoDOT’s specifications.

	For Laboratory testing and sample reporting procedures, refer to [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]].		For Laboratory testing and sample reporting procedures, refer to [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]].
Line 26:		Line 26:

	====1055.2.1.2 Manufacturer and Brand Name Approval====		====1055.2.1.2 Manufacturer and Brand Name Approval====
	If a manufacturer desires to have material added to the Pre-Acceptance List of qualified curing compounds, a certification and guarantee must be submitted to the State Construction and Materials Engineer in accordance with the requirements of [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec1055~~.pdf Sec 1055]. The certification and guarantee shall be accompanied by a one-quart (1 liter) sample of curing compound. Upon approval of the curing compound, it will be placed on the applicable list. Further certification is not required.		If a manufacturer desires to have material added to the Pre-Acceptance List of qualified curing compounds, a certification and guarantee must be submitted to the State Construction and Materials Engineer in accordance with the requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1055]. The certification and guarantee shall be accompanied by a one-quart (1 liter) sample of curing compound. Upon approval of the curing compound, it will be placed on the applicable list. Further certification is not required.

	====1055.2.1.3 Basis of Acceptance====		====1055.2.1.3 Basis of Acceptance====
Line 57:		Line 57:

	====1055.2.3.1 Basis of Acceptance====		====1055.2.3.1 Basis of Acceptance====
	The Supplier shall provide evidence that the Material conforms to the specifications as defined in [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec1055~~.pdf Sec 1055].		The Supplier shall provide evidence that the Material conforms to the specifications as defined in [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1055].

	====1055.2.3.2 Sampling====		====1055.2.3.2 Sampling====

Smithk: updated link

2013-10-10T15:02:15Z

updated link

← Older revision		Revision as of 10:02, 10 October 2013
Line 74:		Line 74:
	===1055.3.2 Dissipating Curing Compound===		===1055.3.2 Dissipating Curing Compound===

	A sample record as described by [[106.20 Reporting#106.20.1.1 Automation Section ~~3510~~\|EPG 106.20.1.1 Automation Section ~~3510~~]] and including the Free Form Test will be created for any material accepted on the job on the basis of certifications, label, or invoice.		A sample record as described by [[106.20 Reporting#106.20.1.1 Automation Section\|EPG 106.20.1.1 Automation Section]] and including the Free Form Test will be created for any material accepted on the job on the basis of certifications, label, or invoice.

	If the shipper requests, the material will be assigned a PAL ID per EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds.		If the shipper requests, the material will be assigned a PAL ID per EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds.

Smithk: updated links

2010-07-01T20:03:31Z

updated links

Smithk: /* 1055.3.2 Dissipating Curing Compound */ updated link

2010-07-01T19:23:56Z

1055.3.2 Dissipating Curing Compound: updated link

← Older revision		Revision as of 14:23, 1 July 2010
Line 74:		Line 74:
	===1055.3.2 Dissipating Curing Compound===		===1055.3.2 Dissipating Curing Compound===

	A sample record as described by [[106.10 Automation ~~of Material Procedures~~\|EPG 106.10 Automation ~~of Material Procedures~~]] and including the Free Form Test will be created for any material accepted on the job on the basis of certifications, label, or invoice.		A sample record as described by [[106.20 Reporting#106.20.1.1 Automation Section 3510\|EPG 106.20.1.1 Automation Section 3510]] and including the Free Form Test will be created for any material accepted on the job on the basis of certifications, label, or invoice.

	If the shipper requests, the material will be assigned a PAL ID per EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds.		If the shipper requests, the material will be assigned a PAL ID per EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds.

← Older revision		Revision as of 10:34, 13 December 2024
Line 29:		Line 29:

	====1055.2.1.3 Basis of Acceptance====		====1055.2.1.3 Basis of Acceptance====
	Material is accepted by the PAL criteria as indicated in [[106.~~12 Pre~~-~~Acceptance Lists~~ (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]]. The State Construction and Materials Engineer will retain the original certification and guarantee. Additional certification is not necessary if the manufacturer and brand of material is clearly identified on the container or the documentation included with bulk shipments.		Material is accepted by the PAL criteria as indicated in [[106.12_Qualified_Lists_(QL)_and_Pre-Acceptance_Lists_(PAL)\|EPG 106.12 Qualified Lists (QL) and Pre-Acceptance Lists (PAL)]]. The State Construction and Materials Engineer will retain the original certification and guarantee. Additional certification is not necessary if the manufacturer and brand of material is clearly identified on the container or the documentation included with bulk shipments.

	All storage tanks shall provide a means for sampling and for mechanical mixing to prevent settling of material. In addition, a project storage tank shall provide a metering device so that all material for the project may be metered into the spray apparatus to determine coverage rates. Material stored for the project shall be mixed thoroughly by the means designated by the manufacturer, prior to unloading for use at the paving site. Only approved material of the same brand and manufacturer may be mixed in any transport or storage.		All storage tanks shall provide a means for sampling and for mechanical mixing to prevent settling of material. In addition, a project storage tank shall provide a metering device so that all material for the project may be metered into the spray apparatus to determine coverage rates. Material stored for the project shall be mixed thoroughly by the means designated by the manufacturer, prior to unloading for use at the paving site. Only approved material of the same brand and manufacturer may be mixed in any transport or storage.
Line 37:		Line 37:

	====1055.2.1.5 Manufacturing Facility====		====1055.2.1.5 Manufacturing Facility====
	Each curing compound manufacturer will be assigned to a district office for Facility Review, Sampling and Testing in accordance with [[106.~~12 Pre~~-~~Acceptance Lists~~ (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]]. During the visit, samples of material available at the facility shall be obtained. Material originating too far from the assigned district’s office is subject to sampling at an intermediate location or at the job site. It is the assigned district’s responsibility to verify with the supplier that the location selected for sampling is acceptable to the supplier as a location from which a valid PAL source sample may be obtained.		Each curing compound manufacturer will be assigned to a district office for Facility Review, Sampling and Testing in accordance with [[106.12_Qualified_Lists_(QL)_and_Pre-Acceptance_Lists_(PAL)\|EPG 106.12 Qualified Lists (QL) and Pre-Acceptance Lists (PAL)]]. During the visit, samples of material available at the facility shall be obtained. Material originating too far from the assigned district’s office is subject to sampling at an intermediate location or at the job site. It is the assigned district’s responsibility to verify with the supplier that the location selected for sampling is acceptable to the supplier as a location from which a valid PAL source sample may be obtained.

	====1055.2.1.6 Sample====		====1055.2.1.6 Sample====
Line 66:		Line 66:
	===1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds===		===1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds===

	Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.~~12 Pre~~-~~Acceptance Lists~~ (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]].		Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.12_Qualified_Lists_(QL)_and_Pre-Acceptance_Lists_(PAL)\|EPG 106.12 Qualified Lists (QL) and Pre-Acceptance Lists (PAL)]].

	For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [https://www.modot.org/sites/default/files/documents/construction_and_materials/material_qualified_product_listing/gs013f3.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.		For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [https://www.modot.org/sites/default/files/documents/construction_and_materials/material_qualified_product_listing/gs013f3.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.
Line 80:		Line 80:
	===1055.3.3 Waterproof Paper, White Polyethylene-Burlap Sheeting, and Burlap and Mats===		===1055.3.3 Waterproof Paper, White Polyethylene-Burlap Sheeting, and Burlap and Mats===

	Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.~~12 Pre~~-~~Acceptance Lists~~ (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]].		Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.12_Qualified_Lists_(QL)_and_Pre-Acceptance_Lists_(PAL)\|EPG 106.12 Qualified Lists (QL) and Pre-Acceptance Lists (PAL)]].

← Older revision		Revision as of 08:01, 28 September 2023
Line 6:		Line 6:
	==1055.1 Apparatus==		==1055.1 Apparatus==

	a) Clear or Transparent Liquid and White Pigmented Curing Compounds. The sample containers for materials shown in [[:Category:1055 Concrete Curing Material#1055.2.1.1 Pre-Acceptance Lists\|EPG 1055.2.1.1 Pre-Acceptance Lists]] and [[:Category:1055 Concrete Curing Material#1055.2.1.2 Manufacturer and Brand Name Approval\|EPG 1055.2.1.2 Manufacturer and Brand Name Approval]] shall be one quart (1 liter) ~~screw~~ top cans which are dry and free from contamination. All sample containers, labeling, and marking materials are to be as described in [[106.3 Samples, Tests and Cited Specifications#106.3.1.2.3 Rush Tests\|EPG 106.3.1.2.3 Rush Tests]] and [[106.3 Samples, Tests and Cited Specifications#106.3.1.3 Sampling Supplies\|EPG 106.3.1.3 Sampling Supplies]].		a) Clear or Transparent Liquid and White Pigmented Curing Compounds. The sample containers for materials shown in [[:Category:1055 Concrete Curing Material#1055.2.1.1 Pre-Acceptance Lists\|EPG 1055.2.1.1 Pre-Acceptance Lists]] and [[:Category:1055 Concrete Curing Material#1055.2.1.2 Manufacturer and Brand Name Approval\|EPG 1055.2.1.2 Manufacturer and Brand Name Approval]] shall be one quart (1 liter) friction top lined cans which are dry and free from contamination. All sample containers, labeling, and marking materials are to be as described in [[106.3 Samples, Tests and Cited Specifications#106.3.1.2.3 Rush Tests\|EPG 106.3.1.2.3 Rush Tests]] and [[106.3 Samples, Tests and Cited Specifications#106.3.1.3 Sampling Supplies\|EPG 106.3.1.3 Sampling Supplies]].
	{\|style="padding: 0.3em; margin-left:1px; border:2px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="280px" align="right"		{\|style="padding: 0.3em; margin-left:1px; border:2px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="280px" align="right"
	\|-		\|-
Line 23:		Line 23:

	====1055.2.1.1 Pre-Acceptance Lists====		====1055.2.1.1 Pre-Acceptance Lists====
	Manufacturers and Brand Names of white pigmented liquid membrane curing compounds and clear or transparent liquid membrane curing compounds will be placed on the Pre-Acceptance List maintained by the State Construction and Materials Engineer in ~~accordance with EPG 1055.2.1.2 Manufacturer~~ and ~~Brand Name Approval, below,~~ and the applicable specification. These lists are found in the Pre-Acceptance Lists & PAL Forms and on MoDOT’s web site.		Manufacturers and Brand Names of white pigmented liquid membrane curing compounds and clear or transparent liquid membrane curing compounds will be placed on the Pre-Acceptance List maintained by the State Construction and Materials Engineer upon completion of testing in AASHTO Product Evaluation and Audit Solutions Concrete Curing Compounds program and meets the applicable specification. These lists are found in the Pre-Acceptance Lists & PAL Forms and on MoDOT’s web site.

	====1055.2.1.2 Manufacturer and Brand Name Approval====		====1055.2.1.2 Manufacturer and Brand Name Approval====
	If a manufacturer desires to have material added to the Pre-Acceptance List of qualified curing compounds, a certification and guarantee must be submitted to the State Construction and Materials Engineer in accordance with the requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1055]. The certification and guarantee shall be accompanied by a one-quart (1 liter) sample of curing compound. Upon approval of the curing compound, it will be placed on the applicable list~~. Further certification is not required~~.		If a manufacturer desires to have material added to the Pre-Acceptance List of qualified curing compounds, a certification and guarantee must be submitted to the State Construction and Materials Engineer in accordance with the requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1055]. The certification and guarantee shall be accompanied by a one-quart (1 liter) sample of curing compound. Upon approval of the curing compound, it will be placed on the applicable list.

	====1055.2.1.3 Basis of Acceptance====		====1055.2.1.3 Basis of Acceptance====
Line 40:		Line 40:

	====1055.2.1.6 Sample====		====1055.2.1.6 Sample====
	A sample of curing compound shall consist of one quart (1 liter) of material in a ~~screw~~ top can. All samples shall be obtained by the manufacturer or contractor’s agent in accordance with the manufacturer’s sampling instructions. The inspector will observe the sampling process. The sample shall be recorded through AASHTOWARE Project (AWP) showing the manufacturer's name, the brand name and designation of the material, lot number, net quantity represented, and the location where the sample was obtained using the Sampled From and Sample Origin fields of AWP. The Other tab is also used for a Mixing Facility. The PAL ID number obtained by the supplier in accordance with EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds should be recorded in Site Manager in the “Link To” field.		A sample of curing compound shall consist of one quart (1 liter) of material in a metal friction top lined can. All samples shall be obtained by the manufacturer or contractor’s agent in accordance with the manufacturer’s sampling instructions. The inspector will observe the sampling process. The sample shall be recorded through AASHTOWARE Project (AWP) showing the manufacturer's name, the brand name and designation of the material, lot number, net quantity represented, and the location where the sample was obtained using the Sampled From and Sample Origin fields of AWP. The Other tab is also used for a Mixing Facility. The PAL ID number obtained by the supplier in accordance with EPG 1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds should be recorded in Site Manager in the “Link To” field.

	===1055.2.2 Dissipating Curing Compound===		===1055.2.2 Dissipating Curing Compound===

← Older revision		Revision as of 15:03, 1 July 2010
Line 29:		Line 29:

	====1055.2.1.3 Basis of Acceptance====		====1055.2.1.3 Basis of Acceptance====
	Material is accepted by the PAL criteria as indicated in [[106.2 Pre-Acceptance Lists (PAL)\|EPG 106.2 Pre-Acceptance Lists (PAL)]]. The State Construction and Materials Engineer will retain the original certification and guarantee. Additional certification is not necessary if the manufacturer and brand of material is clearly identified on the container or the documentation included with bulk shipments.		Material is accepted by the PAL criteria as indicated in [[106.12 Pre-Acceptance Lists (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]]. The State Construction and Materials Engineer will retain the original certification and guarantee. Additional certification is not necessary if the manufacturer and brand of material is clearly identified on the container or the documentation included with bulk shipments.

	All storage tanks shall provide a means for sampling and for mechanical mixing to prevent settling of material. In addition, a project storage tank shall provide a metering device so that all material for the project may be metered into the spray apparatus to determine coverage rates. Material stored for the project shall be mixed thoroughly by the means designated by the manufacturer, prior to unloading for use at the paving site. Only approved material of the same brand and manufacturer may be mixed in any transport or storage.		All storage tanks shall provide a means for sampling and for mechanical mixing to prevent settling of material. In addition, a project storage tank shall provide a metering device so that all material for the project may be metered into the spray apparatus to determine coverage rates. Material stored for the project shall be mixed thoroughly by the means designated by the manufacturer, prior to unloading for use at the paving site. Only approved material of the same brand and manufacturer may be mixed in any transport or storage.
Line 37:		Line 37:

	====1055.2.1.5 Manufacturing Facility====		====1055.2.1.5 Manufacturing Facility====
	Each curing compound manufacturer will be assigned to a district office for Facility Review, Sampling and Testing in accordance with [[106.2 Pre-Acceptance Lists (PAL)\|EPG 106.2 Pre-Acceptance Lists (PAL)]]. During the visit, samples of material available at the facility shall be obtained. Material originating too far from the assigned district’s office is subject to sampling at an intermediate location or at the job site. It is the assigned district’s responsibility to verify with the supplier that the location selected for sampling is acceptable to the supplier as a location from which a valid PAL source sample may be obtained.		Each curing compound manufacturer will be assigned to a district office for Facility Review, Sampling and Testing in accordance with [[106.12 Pre-Acceptance Lists (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]]. During the visit, samples of material available at the facility shall be obtained. Material originating too far from the assigned district’s office is subject to sampling at an intermediate location or at the job site. It is the assigned district’s responsibility to verify with the supplier that the location selected for sampling is acceptable to the supplier as a location from which a valid PAL source sample may be obtained.

	====1055.2.1.6 Sample====		====1055.2.1.6 Sample====
Line 66:		Line 66:
	===1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds===		===1055.3.1 Clear or Transparent Liquid and White Pigmented Curing Compounds===

	Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.2 Pre-Acceptance Lists (PAL)\|EPG 106.2 Pre-Acceptance Lists (PAL)]].		Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.12 Pre-Acceptance Lists (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]].

	For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [http://www.modot.mo.gov/business/materials/pdf/vol_1/GS013F3.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.		For material shipped directly to a job site by a supplier, the supplier shall notify the State Construction and Materials Engineer prior to shipment using [http://www.modot.mo.gov/business/materials/pdf/vol_1/GS013F3.pdf GS-13 Form 3]. When complete and correct information on the shipment is provided to the State Construction and Materials Engineer, a PAL ID number will be assigned to the material. That number shall be attached to the material or container and stay with the material until it is consumed.
Line 80:		Line 80:
	===1055.3.3 Waterproof Paper, White Polyethylene-Burlap Sheeting, and Burlap and Mats===		===1055.3.3 Waterproof Paper, White Polyethylene-Burlap Sheeting, and Burlap and Mats===

	Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.2 Pre-Acceptance Lists (PAL)\|EPG 106.2 Pre-Acceptance Lists (PAL)]].		Test results shall be reported by the Laboratory in accordance with [[1055.4 Laboratory Testing Guidelines for Sec 1055\|EPG 1055.4 Laboratory Testing Guidelines for Sec 1055]] and [[106.12 Pre-Acceptance Lists (PAL)\|EPG 106.12 Pre-Acceptance Lists (PAL)]].