901.18 Laboratory Testing for Sec 901 - Revision history

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-09-14T16:12:26Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 11:12, 14 September 2021
Line 6:		Line 6:
	===Bolts, Nuts, and Washers===		===Bolts, Nuts, and Washers===

	Chemical tests consisting of mass of coating shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through ~~AASHTOWare~~.		Chemical tests consisting of mass of coating shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AASHTOWARE Project (AWP).

	Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts\|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through ~~AASHTOWare~~.		Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts\|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through AWP.

	===Polyurethane Foam===		===Polyurethane Foam===
Line 18:		Line 18:
	:(b) Density - ASTM D1622		:(b) Density - ASTM D1622

	Test results and calculations shall be recorded through ~~AASHTOWare~~.		Test results and calculations shall be recorded through AWP.

	==901.18.2 Sample Record==		==901.18.2 Sample Record==

	The sample record shall be completed in ~~AASHTOWare~~, as described in [[:Category:101 Standard Forms#Sample Record General ~~Information~~\| Sample Record General ~~Information]] [[image:bulldozer.jpg\|20px~~]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [http://epg.modot.org/index.php/106.20_Reporting EPG 106.20 Reporting], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AASHTOWARE Project (AWP), as described in [[:Category:101 Standard Forms#Sample Record, General\|AWP MA Sample Record, General]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [http://epg.modot.org/index.php/106.20_Reporting EPG 106.20 Reporting], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:901 Lighting]]		[[Category:901 Lighting]]

Smithk: Per TS, numerous minor clarifications

2020-08-18T19:30:38Z

Per TS, numerous minor clarifications

← Older revision		Revision as of 14:30, 18 August 2020
Line 1:		Line 1:
	This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers and polyurethane foam used in highway lighting. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=13 Sec 901] for MoDOT’s specifications.		This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers, and polyurethane foam used in highway lighting. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=13 Sec 901] for MoDOT’s specifications.


Line 6:		Line 6:
	===Bolts, Nuts, and Washers===		===Bolts, Nuts, and Washers===

	Chemical tests consisting of mass of coating, shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through ~~SiteManager~~.		Chemical tests consisting of mass of coating shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AASHTOWare.

	Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts\|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through ~~SiteManager~~.		Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts\|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through AASHTOWare.

	===Polyurethane Foam===		===Polyurethane Foam===
Line 18:		Line 18:
	:(b) Density - ASTM D1622		:(b) Density - ASTM D1622

	Test results and calculations shall be recorded through ~~SiteManager~~.		Test results and calculations shall be recorded through AASHTOWare.

	==901.18.2 Sample Record==		==901.18.2 Sample Record==

	The sample record shall be completed in ~~SiteManager~~, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [~~[:category~~: 106 ~~Control of Material#Reporting Test Results\|~~Reporting ~~Test Results]~~], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AASHTOWare, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [http://epg.modot.org/index.php/106.20_Reporting EPG 106.20 Reporting], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:901 Lighting]]		[[Category:901 Lighting]]

Smithk: updated link

2016-06-15T14:30:17Z

updated link

← Older revision		Revision as of 09:30, 15 June 2016
Line 1:		Line 1:
	This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers and polyurethane foam used in highway lighting. Refer to [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec0901~~.pdf Sec 901] for MoDOT’s specifications.		This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers and polyurethane foam used in highway lighting. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=13 Sec 901] for MoDOT’s specifications.

Smithk: updated link

2013-08-22T17:13:14Z

updated link

← Older revision		Revision as of 12:13, 22 August 2013
Line 22:		Line 22:
	==901.18.2 Sample Record==		==901.18.2 Sample Record==

	The sample record shall be completed in SiteManager, as described in [~~http~~:~~//contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510~~.~~pdf Automation Section 3510~~], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:901 Lighting]]		[[Category:901 Lighting]]

Smithk: /* 901.18.2 Sample Record */ Per CM, updated link to AS 3510

2011-07-05T20:16:37Z

901.18.2 Sample Record: Per CM, updated link to AS 3510

← Older revision		Revision as of 15:16, 5 July 2011
Line 22:		Line 22:
	==901.18.2 Sample Record==		==901.18.2 Sample Record==

	The sample record shall be completed in SiteManager, as described in [http://~~wwwi~~/~~intranet~~/cm/~~materials~~/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.


	[[Category:901 Lighting]]		[[Category:901 Lighting]]

Smithk: /* 901.18.1 Procedure */ minor clarification

2010-03-30T18:28:26Z

901.18.1 Procedure: minor clarification

← Older revision		Revision as of 13:28, 30 March 2010
Line 8:		Line 8:
	Chemical tests consisting of mass of coating, shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.		Chemical tests consisting of mass of coating, shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.

	Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts\|712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through SiteManager.		Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts\|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through SiteManager.

	===Polyurethane Foam===		===Polyurethane Foam===

Smithk: article construction

2008-03-05T21:17:25Z

article construction

New page

This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers and polyurethane foam used in highway lighting. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec0901.pdf Sec 901] for MoDOT’s specifications.

==901.18.1 Procedure==

===Bolts, Nuts, and Washers===

Chemical tests consisting of mass of coating, shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.

Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts|712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through SiteManager.

===Polyurethane Foam===

Tests on samples of polyurethane foam shall be conducted in accordance with the following methods:

:(a) Compressive Strength - ASTM D1621

:(b) Density - ASTM D1622

Test results and calculations shall be recorded through SiteManager.

==901.18.2 Sample Record==

The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results|Reporting Test Results]], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

[[Category:901 Lighting]]